There are several ways to make such toys. For example, you can make a butterfly knife out of paper. This toy can be made in just a few minutes.

What materials will be needed

For self-made safety knife you will need:

• several sheets of thick paper 15x20 cm - 2 red, 2 blue, 1 yellow.
• sharp scissors;
• several wooden toothpicks;
• transparent tape.

Also, to assemble a plausible paper knife, you will need to prepare an awl.

Knife blanks

To make a paper knife with your own hands, take a red sheet, fold it in half along long side and cut into two equal parts. Fold each piece in half again and fold it into thirds to create a strip about 1cm wide.

Do the same with the second red leaf. You should end up with 4 identical red stripes. In the future, these will be the “handles” of the knife. Wrap the strips with tape to prevent them from unraveling.

Also fold a sheet of blue paper in half and cut it into two parts. Fold one of the halves in half, then in half again, and again. Cut off the end of the resulting wide strip in the form of a knife tip and wrap the resulting “blade” with tape.

From the second blue half, roll up a narrower strip, folding it in half and then three times. Also cut off its blade-shaped end. Insert a second strip into the first to make the “blade” more rigid.

Cut the second sheet of blue paper in half. Roll a wide strip from one of the halves. Cut the blunt end of the “blade” along the edges along the length by 2-3 cm. Insert the blue strip at the bottom of the “blade” perpendicularly and secure it with tape.

How to make a safe knife out of paper: assembly

At the intersection of the “blade” and the strip, make two holes with an awl. Insert a toothpick into the holes. Punch holes in the ends of each of the 4 red strips you made earlier.

Roll a yellow sheet of paper into a thin tube and secure it with tape. Cut two lengths from the tube equal to the length of the red stripes.

Place the red stripes on both sides of the toothpicks. Coat the yellow tubes with glue on both sides, place them between the red stripes in pairs and press down. As a result, you will have two movable handles along the edges of the “blade”.

The final stage

Cut the toothpicks so that they protrude only a couple of millimeters beyond the plane of the paper. Cover them with tape on both sides.

Cut the perpendicular blue strip at the level of the “handles”. A real paper butterfly knife for a child is ready. Depending on the position of the “handles”, the “blade” in such a toy will be open or closed.

Today it is very fashionable to manufacture products based on paper. Toys of this type can completely replace real ones. Take, for example, pistols or knives. Unlike plastic options, paper ones are safe, which is primarily important for children. One of the main attributes of toys for boys is a knife. We recommend that you read the instructions below and learn how to make a knife out of paper.

Knife made of multi-colored paper

To begin with, we will tell you how to make a knife from colored paper. To construct this model of a children's toy, you will need an A4 sheet, a stapler (can be replaced with tape), and scissors.

Making a knife:

1. We take a sheet, carefully wrap any of the corners, but the edges of the sheet should coincide. Having made such a fold, you should get an open triangle, cut it off, unfold the workpiece and see a square in front of you. We bend the square three times, while ironing the folds well.
2. Now we take scissors and make all the edges semicircular, like a kitchen knife. To prevent the workpiece from falling apart, it must be secured with tape or a stapler. Now we take a piece, bend it along its length several times, fix it with the same tape and get the handle of our knife.
3. Next you need to combine 2 blanks into one solid object. After joining, the craft can be painted.

So we told you how to make a knife out of paper simple option. Now you can start making a more complex model.

Kunai Dagger

One of the serious paper products can be called a Kunai knife. The paper art of origami is used to construct it. Before you begin the manufacturing process, you need to find two landscape sheets and several sheets of colored paper.

How to make a ninja knife from paper:

1. We take a landscape sheet as a basis, fold it and get a triangular shape. Fold the resulting triangle in half, and then unfold the workpiece to its original position.
2. We wrap the corners to the center line and fold the craft in half. Next, we have protruding ends, which we bend into the resulting pockets and thus form the blade of our future craft.
3. Pressing the edge in the shape of a pyramid with your fingers, we lift the paper a little to achieve volume. We take a second sheet of paper, roll it into a tube with a small diameter and insert the blade five centimeters deep.
4. Next, use your fingers or a sharp object to level the edge of the tube and repeat folding several more times. A handle with a tip should form. At the end, we fix the craft.

Many people want to make the craft heavier and put a coin or pebble in the middle. This is how a ninja knife is made, there are many more options for making knives. Many are trying to learn how to make karambit from paper, we will also tell you about that, but a little later.

Pirate knife

The design of a knife is carried out using the following tools and materials:

• cardboard, preferably white;
• a simple pencil;
• bolt with nut or rivet;
• glue and needle.

Manufacturing process:

• download the template, print it and cut it out;
• take white cardboard, apply the cut out elements, trace them with a pencil, and cut them out too;
• now we take a needle and pierce the blade, body and saw all at once, pull out the needle and insert a bolt or rivet;
• Next, we take glue and drip a little onto the workpiece, but it is worth considering that the blade should not be in the glue;
• then we place one part of the body on the other and fix the workpiece.

The knife is ready, now you can decorate it, if you wish, of course. So we have made the main versions of knives, now we will tell you how to make a karambit knife out of paper.

Karambit

Before explaining how to make karambit from paper, you need to find paper for schematic drawing, a glue stick, and scissors. Boys who play computer games will be interested in making a model themselves. The manufacturing process is very simple:

• download and print the knife drawing;
• Using scissors, we cut out all the parts, apply the blanks to drawing paper and trace them with a pencil, while the base needs to be traced eleven times, and the handle twelve times;
• cut out the outlined elements, glue all the parts and place them under a press (or under heavy books);
• now we take one part of the handle and glue it to the blade;
• Having coated the second part with glue, close the other side of the blade.

At the end, we paint the craft and cover it with colorless varnish.

Knife like an Assassin

This model of knife can be made without a template. You will need eight album sheets and tape.

The knife is made in this way:

The knife is ready. Your child will probably ask you how to make such a paper knife 232 times, and maybe more, because the toy turns out to be excellent. In addition to it, you can make sure that the warrior is ready for battle. We described earlier how to make shuriken.

When playing with such a knife, the child will be safe and will not be injured during the game, and this is a guarantee of peace of mind for parents. It’s better to make any of them together with your children; they will really like this activity.

Each boy in the toy box has attributes such as plastic guns, swords, knives. And very often, manipulations with such dummy weapons are a cause for concern for parents, because the child can injure himself or harm other family members and pets. But is it possible to prohibit a future man from having a toy weapon in his arsenal? Of course not. And so that such entertainment is safe for the health of all household members, we suggest you learn how to make attributes for games with your own hands from scrap materials.

Learning to make toy edged weapons from paper

In this article you will find information on how to make a knife out of paper. Readers are presented with two ways to perform this accessory.

The first model was made using the origami method. A paper knife according to the following description is simple and quick to make. Even a child can easily master this method of making toy weapons. The second version of the knife is made using the papier-mâché method, which children can also do. So, here are the master classes.

How to make a knife out of paper using the origami method?

To work you will need A-4, scissors and a stapler.

When making this model, you can use tape instead of a stapler. To give the craft rigidity, blades can be inserted into the part wooden stick from ice cream.

We make toy weapons from papier-mâché

Do you want to know how to make a knife out of paper this way? Then study the description. We prepare the following materials for work:

• wooden blank of appropriate shape;
• newspapers;
• bowl of water;
• PVA glue;
• sandpaper;
• paints;
• acrylic lacquer.

Cover the blank or finished plastic toy with wet pieces of newspaper in one layer. Next, dilute the glue with water and treat the paper for the next three tiers with this solution. And glue the last layer with clean PVA. Leave the craft until completely dry. Then carefully cut it, take out the shape, and glue both paper parts together. When the product is completely dry, clean it and paint it. And the last stage of work is processing the craft with varnish.

You have learned two ways to make a knife out of paper. We hope that you will find them useful, and very soon your son will be playing with an original, and most importantly, safe toy.

Origami weapons are an attractive activity not only for boys, but also for connoisseurs of various types of weapons who are passionate about the art of creating paper figures.

You can make edged weapons (knives, blades, swords) and firearms (pistols, shotguns, revolvers) from paper. Special templates for origami weapons are not needed; everything is made from paper squares and rectangles. Such crafts can be used as toys or props for productions and costume parties. Paper cannot be used to injure anyone, and if broken, it is easy to reassemble the sword or pistol from a suitable sheet.

Most of the presented master classes contain assembly diagrams that are easy to understand for beginners and children.

Speaking about ninja weapons, one cannot help but recall shuriken - a traditional Japanese melee weapon in the shape of a star with several rays-blades. Typically, an origami shuriken is folded from two paper squares and has four corners. Shuriken is easy to fold using modular technology origami. Beginners can also cope with this task.

This master class suggests making two types of shuriken - with 4 and 8 rays. For a traditional shuriken you will need one single-color square or two multi-colored rectangles, scissors and a little time.

How to make origami shuriken from one square. You need to bend the square in half and cut it along the fold. Bend the resulting rectangles lengthwise.

Bend the corners on each workpiece as shown in the picture (mirror image). Fold them again in a mirror image to each other and turn them over.

To connect the resulting origami figures, place one module on top of another crosswise and tuck the free corners of one module (fold along the lines shown) into the pockets of the other. Turn the origami workpiece over and also tuck the free ends of one piece into the pockets of the other.

An 8-pointed shuriken consists of 8 squares - future modules. Shuriken can be one-color, two-color or multi-colored. To assemble an 8-pointed origami shuriken, you need to follow these steps step by step: bend the square crosswise diagonally and unfold it. Combine left side with a diagonal fold.

Fold the top side of the square back along the diagonal line. Fold the side along the red line, aligning points C and B, as shown in the photo. Turn the origami workpiece on its side and bend it in half along the red line, aligning the green lines.

Fold the bottom corner - the first module is ready.

Repeat steps 1-6 with the remaining 7 squares to make 8 origami modules.

Start combining all the modules: bend them upper layer module and slip another into his pocket.

Tuck the previously folded edge into the pocket of the attached figure.

Connect the remaining modules in the same way.

After joining last detail turn the “ninja weapon” over and tuck the end of the first part into the pocket of the last one.

More complex origami shuriken figures can be assembled from the modules. The photo below shows a few ideas:

In addition to shuriken, ninjas rarely do without a special combat knife - a kunai. It is proposed to make it according to the diagram and video below:

Another cold weapon made of paper is the ninja sword. detailed instructions assembly is presented in the video.

Video: Origami sword for real ninjas

MK is dedicated to creating with your own hands various models firearms using origami technique.

The simplest pistol can be easily made from a square sheet. To do this, you need to wrap the edges on both sides to form a rectangle and bend it in half. Then bend the edge of the workpiece diagonally inward - you get a handle. To form the muzzle, bend the top edges down.

A more elegant pistol is assembled from two rectangles. To do this, you need to perform the following steps step by step:

• folding the wide side, roll both rectangles into two strips - wide and narrow;
• bend each piece in half;
• Wrap the wide strip in a loop, insert the narrow strip into it and pull it up to form a handle and barrel.

A gun is a necessary tool for hunting. It is made according to the same principle as the previous pistol model. A schematic description of the actions is presented below:

A shooting pistol is suitable for games, which you can make yourself in several ways. An origami gun can fire rubber bands or paper. In addition to prepared square and rectangular sheets of paper, you will need glue and tape.

For a better understanding and successful assembly of the origami crossbow pistol, we suggest watching several videos with step-by-step instructions.

Video: Origami crossbow pistol

Now with such an arsenal you can start game shooting.

How to make a knife out of paper

A paper knife is an absolutely safe thing. It's perfect to complement your look at a masquerade party or Halloween. We offer you several detailed workshops on making paper knives. Choose the one you like and get to work!

Master class No. 1: Ninja dagger (kunai)

First, let's look at a simple lesson in the origami technique. This is an indispensable attribute of a modern ninja - kunai.

1. Fold a square piece of paper diagonally to form a right triangle

2. Fold the resulting triangle in half

3. Expand the figure to its original position, then bend each of the corners so that the edge coincides with the center fold line

4. Fold the resulting figure in half along the center fold line

5. Tuck the ends of the paper into the “pocket” on one side of the folded figure. This will be the tip of your dagger

6. Take another sheet of paper and roll it into a thin tube. Push the tube into the “pocket” on the tip of the dagger about 3/4 of its way

7. Smooth out the outer end of the tube (about a third of its length), then bend it to the side at a 90-degree angle

Lesson #2: Cardboard Swiss Army Knife

A folding knife with a red body has become a classic symbol of the Swiss army, and a folding knife-postcard will be an excellent souvenir for any connoisseur of edged weapons.

1. Download the template here and print it.

2. Transfer all the details onto white cardboard and cut them out.

3. Place the file and blade on the back of the body and use a thick needle to pierce all three pieces together. Insert a rivet into the hole (you can buy these at office supply or craft stores).

4. Apply a little thick glue to the areas indicated by the red dots. Make sure that the glue does not get on the side of the knife from which its blades will extend.

5. Place the front half of the body on the back half so that their contours completely coincide.

6. Apply "engraving" to the blades

All! Your personal Swiss knife ready!

Instruction No. 3: Cardboard butterfly knife

Another common model, the so-called “butterfly”, can be made entirely from cardboard or from cardboard and foam board. The peculiarity of this knife is that it can be opened or closed, with one movement of the hand turning the blade case into a handle and back.

1. Download and print the template. You will find it here.

2. Place the cut paper blade pieces onto the sheet corrugated cardboard and cut out all the parts. For the handle body, regular thick cardboard is used.

3. Glue two narrow strips of corrugated cardboard onto the inner surface of the handle halves, as shown in the photo. Don't miss this detail, otherwise the blade of your knife will not be able to move freely.

5. Now pierce the bottom of the blade with a toothpick. Make sure that it protrudes about 1cm on both sides of the cardboard (cut off the excess) and secure the structure with hot glue.

6. All that remains is to connect the handle and blade. To do this, insert the latter into the body, close it, and pierce all three parts with toothpicks at the base - one on each side.

7. Make sure the blade comes out of the handle freely and secure the toothpicks to the outside of the body with hot glue.

Master class No. 4 Knife with a retractable blade

For this project you will need thick and rigid cardboard or foam board. When you press the trigger, the blade pops out of the handle.

1. Download the template and cut it out.

2. Transfer all the fragments to cardboard or foam board and cut out the necessary parts.

3. Stick two squares on top of each other bigger size(all edges must match exactly) - this is the future stopper for the blade. Then, in the same way, connect two smaller squares - the future “trigger”.

4. Now glue the stopper to the side of the future handle, right above the hole (it should remain completely open).

5. Connect the handle fragments as shown in the photo, and then glue the body cover and hilt on top.

Please note that the holes on opposite sides of the case match exactly, and the stopper is visible inside. When you put the rubber band through the holes that will fire the blade, this little part will prevent it from falling out of the handle before you pull the trigger.

6. Pass a piece of rubber band through the holes and, slightly pulling, secure it with hot glue on both sides of the handle.

7. Insert the blade into the handle, simultaneously pulling the elastic band with its base. The notch should be on the side of the stopper and coincide with it.

8. Insert the trigger into the hole under the stopper. It should slide easily in its nest without falling out.

Pulling the “trigger” will cause the blade to move to the side and jump off the stopper, and the tension of the elastic will push it out.

9. Paint the body of the knife and, if desired, the blade.

In this tutorial you will see how to make a simple origami knife that is quite easy to fold.

Nowadays it is considered very fashionable to be able to make all sorts of things out of paper, especially if you use rare techniques. Such items can be an excellent alternative to the real thing, but at the same time be completely safe. This is especially important when it comes to children who are planning a game involving knives. Also, our tips on how to make a knife out of paper will help participants in masquerades and theatrical performances find inexpensive and suitable props.

Content:

Knife made of colored paper

The simplest model of a knife is made using a regular sheet of A4 size, double-sided tape or a stapler and scissors.

Follow these steps:

Making a ninja dagger (kunai) from paper

To make such a superhero knife, you should use the origami technique.

Before you start, prepare two regular office sheets of white or colored paper.

Completing of the work:

The ninja dagger is ready.

Advice! If you want to make your paper weapon a little heavier, place pebbles or coins inside the blade.

Pirate knife

A pirate knife for a children's game or theatrical performance is best made from cardboard.

On a cardboard sheet the right size Draw a pencil shape of the pirates' bladed weapon and cut it out. Then attach the cut out sample, trace it on the cardboard and cut it out again. Make sure all edges match.

After the 2 parts are ready, you need to glue them and paint them. Or you can wrap the blade with shiny foil and cover the handle with colored paper.

Making a butterfly knife out of cardboard

When starting to create this type of knives, you should know that this is not an easy task, and it is also time-consuming. But the result will surprise everyone, including children. The paper version will be exactly the same as the real one.

To work you will need the following materials and tools:

• White paper;
• colored paper;
• scissors;
• glue;
• stationery knife.

Take a sheet of white paper, A4 size, and roll it into a tube, smooth it out. Trim the ends to create a blade. To prevent the structure from unfolding, attach it layer by layer with tape. Draw dotted lines. You need to cut the future craft using them.

Looking at the photo above, mark the workpiece.

The next step is to roll out white sheets (4 pcs) of A4 and red (1 pc) tubes. Place the white tube into the red one.

The red tube should be used like this: 2 identical parts resembling wheels are cut off from it. You need to apply glue to them and connect them by winding them inside one and the other ear.

Mark a hole near the base of the blade. You need to insert one red tube there. And the ends of the second red tube are glued with the tips inward.

To make the handle stronger, glue a white one to the red tube, maintaining the length. Repeat the above on the other side of the handle.

You should end up with a paper version of the butterfly knife.

There is another option for creating a butterfly knife, which uses cardboard or foam board.

The first step is to download the template and then print it.

Let's get to work.

The work on the knife is finished.

Folding Swiss knife made of cardboard

The knife got its name because it was in the Swedish army that they carried such a red bladed weapon. Now we will make a knife - a postcard, which can be used both in the game and as a souvenir.