Most women and men wear wedding rings as a sign of fidelity to each other, simple rings as jewelry. But when faced with a choice for the first time, many do not know the required volume. Any jewelry store will provide you with the service of determining the diameter of your finger, but there are cases when you need to know the size in advance. In this case, the question arises: how to determine the ring size at home?

What is ring size

The ring size refers to its diameter, i.e. the distance between two opposite points on the hole's circumference. Look clearly at the photo below.

To determine the diameter jewelry at home, there are a few things to consider:

• Throughout the day, the size of the fingers changes slightly. Noon is the most the right time to determine the volume. In the morning, my hands are still swollen due to the water accumulated during the night.
• Do not measure after playing sports, when high temperature indoors, right after the cool street.
• It is worth considering that independent measurements will not have high accuracy. This will be an approximate/guideline size.

Choosing jewelry for the ring finger right hand Please note that it may not be the right size for your left hand. If you were given jewelry not suitable size, then in this case contact a jeweler, he will roll it out (increase the diameter a little).

How to determine ring size using a table at home

Let's look at two ways to determine the ring size yourself at home using a table. To do this, you will need to prepare a small piece of thick paper, a pen, a ruler, half a meter of thread (knitting thread is ideal in thickness), and scissors. In addition to plain paper, a checkered piece of paper works well. When taking home measurements, keep in mind that the ring should pass freely through the joint (phalanx).

Using a strip of paper

• First way. Cut a strip from the sheet one to one and a half centimeters wide and up to five centimeters long. Wrap it around the finger you need. Place a mark with a pen where the end of the strip meets. Unfold the paper and use a ruler to measure the distance from the edge to your mark. The length found is the girth; to find the cross section, you need to divide this value by the number 3.14. The size is determined by finding the diameter equal to the table.

• Second way. This option is perfect for men who want to put such a gift on the finger of their beloved girlfriend, having with them another one that matches the inner contour. Take the ring and attach it to the sheet, trace its outline with a pen and a thin marker inside at the base. Find the diameter from the resulting circle. Typically, the difference between sizes is half a centimeter.

Advice. It is worth rounding the result to a lower value for narrow rings, and to a larger value for wide rings.

Using thread

For this home method, take a thick thread (tape), wrap five turns a little tightly and carefully around the selected finger (the width of the winding should not be more than six millimeters). Don't wrap it too tightly. Cross both ends without tearing them away from the coils, cut them off with scissors at the intersection. Or, with a pen, mark the intersection of the ends of the thread, unwind it, and cut it at the marked places. Measure the resulting length of thread with a ruler.

And in order to determine your individual size at home, you should divide the value obtained from the measurement by a special number 15.7. The result must be rounded.

International table

Video: How to make a ring size template at home using coins

Some sites offer templates ready for printing on a printer. But when copying or printing the pattern, the image will be slightly distorted. Therefore, it is better to make a template with your own hands at home.

Watch the video to learn how to make a template for the sizes of the required rings yourself at home:

As you can see, the conditions provided at home allow you to determine the right size for your ring. These methods are not only easy to use, but will also take you a small amount of time.

If you know any other simple, interesting and effective ways, how to determine the size of a ring at home, then leave your comments. They will be useful for other readers.

How to change ring size

Any jewelry or jewelry puts a girl in the mood if they are used for their intended purpose and do not gather dust in a small jewelry box. Therefore, when it comes to rings, they must certainly match the size of the finger.

But, alas, the size of our fingers changes over the years (most often upward). And the given ring or ring may not initially fit the finger on which you so want to see it. And then the need arises to change the ring size, reduce or enlarge it.

Changing the ring size

First of all, it must be said that you can increase or decrease the size of a ring only in a jewelry workshop. It is impossible to do this at home without the appropriate equipment and skills.

1. In the price list of jewelry workshops you will definitely find a repair service for items made of precious metals. You need to be especially careful when changing ring sizes. First of all, study the surface of the product, if it is smooth, then the master will be able to increase it even by 3 sizes, and if there are notches, patterns or stones on the ring, then it will not be so plastic.
2. You must clearly know which finger you will wear the ring on in order to measure the diameter of the desired finger. You should also determine the initial size of the jewelry, visit showrooms and use special devices and size samples.
3. Try on rings in a calm state. During hot weather, after serious physical exertion, or during illness, there may be swelling on the fingers, which will make it difficult to determine the exact size.
4. Inquire about workshops that specialize in fitting and repairing jewelry. The cost of such services should not be artificially high. Seek advice and recommendations from friends and consultants in jewelry stores.
5. Before submitting the product for adjustment, go to several workshops and personally talk with 2-3 craftsmen, discuss the details of the upcoming procedure. If you need to reduce the size of the ring, this can be done by compression (this execution is only suitable for products with a smooth surface). Correct form The ring is ensured by uniform compression on all sides simultaneously. Another method is to cut out a piece of metal, suitable for products with notches. Only very professional craftsmen undertake resizing a product that has an engraving on it, due to the high risk of damage.
6. If you need to cut metal, it is best to make the cut close to the sample, as it will be less noticeable.
7. Repair of platinum products is carried out only with special equipment, which costs a lot of money, so not every workshop can afford it.
8. If the master told you in detail about the upcoming procedure, warned you about possible risks, but offered a guarantee for the quality of the work performed, then you can opt for such a workshop.

Important facts and nuances: how to roll out a ring at home?

The ring is an indispensable decoration for fingers, known since ancient times. Today you can choose a ring of almost any size. But sometimes there is an unpleasant situation - favorite ring suddenly it becomes small, or the gift does not fit on your finger. In this case, rolling it out in a jewelry salon can help. But this is quite expensive, so it is better to find out how to roll out a ring at home and whether it is even possible. It wouldn’t hurt to find out whether this particular product can be enlarged or not.

What kind of rings can you roll out?

Increasing the ring size by rolling has some features that must be taken into account. Unfortunately, many types of rings are not rolled out due to completely natural processes during rolling:

1. Rings with rotating inserts.

2. In most cases, the dimensions of bimetallic rings do not change.

3. If there is a drawing or a stone, this is also prohibited.

Based on this list, the answer to the question whether it is possible to roll out a ring with stones alone is absolutely not. In this case, only one metal base may remain, and the pebbles will leave their nests due to stretching and deformation of the metal.

Is it possible to roll out the ring yourself?

Unfortunately, it is quite difficult to increase your ring size at home. Because for this, at a minimum, you will need experience and a special tool. Not every man has a special deadbolt, a gas burner and a hammer with a rubber surface in his garage or closet. In most cases, a special rolling device is used. But even if all this is present, a lack of experience can lead to irreparable damage to the ring.

But the technology used by jewelers to increase sizes using a crossbar and a special device is quite clear:

· First, the ring is heated red-hot using a gas burner.

· Then they allow it to cool on its own, while preparing the tools.

· The slightly cooled decoration is inserted into the device and gradually rolled out. It is important not to press too hard on the shackle right away, otherwise there is a risk of damaging it.

· Periodically remove the ring and adjust the existing stretch.

· If necessary, the surface is straightened by pressing on the crossbar and polished.

There is one very important nuance that you need to pay attention to. It depends on how long the ring can be rolled out. You need to pay attention to the thickness of the bow. If it is very thin and fragile, it is not recommended to roll it out, as there is a risk of it breaking. But in general, the thicker the bow, the more larger size you can roll it out. Naturally, the rings are not rubber, and stretching from size 13 to 21 will not work. The limit is three or four positions in the best case.

“Network publication “WomansDay.ru (WomansDey.ru)”
Certificate of registration of mass media EL No. FS77-67790,
issued Federal service for supervision in the field of communications,
information technologies and mass communications (Roskomnadzor)
December 13, 2016 16+.
Copyright (c) Hirst Shkulev Publishing LLC. 2017.
Any reproduction of site materials without the permission of the editors is prohibited.
Contact information for government agencies
(including for Roskomnadzor):

Gold has excellent ductility, so if necessary, the size of a gold ring can be relatively easily changed by decreasing or increasing it by one or two sizes. It is not recommended to perform such an operation at home, even if you have the appropriate tools, since in the wrong hands the jewelry can be irreparably deformed.

The most common way to increase ring size is mechanical. The master first checks what the true size of the product is, and then determines how much it needs to be increased. After measurements, the ring is treated with a burner flame. When it cools down, the product is put on a special crossbar. Using a roller that matches the profile of the product, the ring is stretched to the required size. All that remains is to align the ends and polish the ring to its original shine.

There is a more labor-intensive way to increase the ring size. In this case, it is expanded by inserting a piece of metal of a similar standard. First, a joint is formed, where a piece of material is placed and carefully soldered when heated with the flame of a heating pad. The renewed product is then bleached, dried and carefully processed with a jewelry file to remove possible protrusions and depressions.

When choosing a specific method, experts always base it on the size of the ring. For a thin product, simple mechanical stretching is most suitable. If the ring is massive and thick, it is easier and more reliable to use the insertion method. In the simplest case, when the ring needs to be enlarged by just a fraction of a millimeter, sometimes its inner surface is simply bored, removing the thinnest layer of metal.

If the ring has inserts in the form of stones, they are often dismantled before work. This is done in order to reduce the risk of stress appearing in the stone, which may well lead to its irreparable deformation. After increasing the size of the ring, the stones can be easily inserted into place, securing them accordingly.

A wedding ring is a symbol of marriage, so spouses wear it on ring finger right hand as a sign of loyalty to each other. However, there are situations that require increasing its size. Typically, a traditional wedding ring is made of gold, which is malleable. Thus, it will not be difficult for a jeweler to change such an important piece of jewelry by one or two sizes.

Undoubtedly, the complexity of the work is determined directly by the master and it depends specifically on the type of wedding ring: smooth or with stones. It is necessary to take into account that the pricing policy of each individual company is varied, so you need to contact only those specialists who do not raise any doubts about their professionalism and competence. Otherwise, such an important element of the marriage risks being damaged irrevocably.

The main ways to increase the size of a wedding ring are: stretching the metal on the crossbar, as well as inserting a piece of gold of the same standard. First of all, the jeweler measures the exact size of the ring, after which he determines exactly how much the product should be enlarged. Then, the master anneals the ring with the flame of a special burner and when it cools down a little, he places the crossbar on the tension roller prepared. After this, a roller is installed, which in shape corresponds to the profile of the gold jewelry. Next, the jeweler, rotating the handle of the crossbar, moves the guide axis and, accordingly, the clamping handle, and with his free hand he presses the roller to the ring, ensuring that it is seated on the crossbar. Thus, when the ring reaches the desired size, the master will wash it, bleach it and straighten the ends of the ring. Ultimately, the product is polished, thereby acquiring its original shine.

If the jewelry is enlarged by inserting a piece of gold, then it is necessary to apply small fragments of this metal of the same standard to the joint, and then solder them under the flame of a burner. After which the jewelry is bleached, dried and the inserted piece is adjusted so that there are no protrusions or depressions. It should be noted that if wedding ring thin, then best method changes in its size will result in mechanical stretching. On the contrary, a thick ring, as a rule, is difficult to stretch, so it is advisable to insert a piece of gold.

Enlargement of a gold ring with stones is mainly carried out experienced craftsman in the following sequence: removes the stone from the mount, performs certain procedures with this metal in order to change the size, and then inserts the stone back. It must be remembered that such an increase in the size of a ring with a stone will cost the client much more.

How to change ring size?

Today, methods that allow adjust the ring to the desired size. worked to perfection.

In a jewelry workshop, such work can be completed in the presence of the customer in 10-15 minutes. The main thing is that the ring falls into the capable hands of a jeweler who has earned positive reviews for his work.

How to reduce ring size?

To make a ring smaller, jewelers use three methods.

• Cutting out a piece of the rim.

This method is applied to rings decorated precious stones to prevent damage to the overall structure of the decoration. It is recommended to first remove all stones from the setting, especially when soldering the ring with an open fire.

For rings made of white gold, with enamel or mother of pearl, laser soldering is used.

If the ring is one size too big. The jeweler cuts a piece of the base 3.14 mm long, into two sizes - 6.28 mm, and then grinds and polishes the joint.

This method is usually used to reduce the size of wedding rings without precious stones or decorative elements.

If the ring needs to be adjusted by half a size, it is simply knocked down, and if by 1-1.5-2 sizes, it is preheated, increasing the elasticity of the metal, and then knocked down to the desired size. The carbon deposits are cleaned off and the product is polished.

• Insertion without sawing.

The method is expensive, but eliminates all signs of impact on the decoration. The ring remains the same, only its inner diameter decreases. This happens by soldering a base metal plate or an additional ring into the inside of the product.

How to increase your ring size?

In this case, jewelers also practice three methods.

The method is simple, but applicable only for rings with a thick rim that need to be increased by half a size. Its main disadvantage is the loss of ground gold, however, sometimes this method is the only one that allows you to increase the size of a complex-shaped ring with stones or decor without damage.

This method is used to increase the size of ordinary wedding and signet rings. The ring should not be too wide - no more than 10-12 mm. It is easier to stretch thin rings, even by 2 sizes, but this method is not suitable for too thin products - they may burst.

The jeweler first determines the amount by which the ring should be enlarged, then heats the product, puts it on the crossbar and, by rotating its handle, achieves the required size. At the end of the work, removes irregularities, grinds and polishes the ring.

A ring with a complex ornament or stone setting can be increased in size only by making an insert made of a similar metal. The product is cut from the bottom and expanded to the right size, and a pre-prepared insert is soldered into the resulting space. Before soldering, the insert and ring are boiled in boric acid to maintain shine. After final processing, the ring looks like a single whole.

MOST INTERESTING NEWS

Today, methods that allow adjust the ring to the desired size, worked to perfection.

In a jewelry workshop, such work can be completed in the presence of the customer in 10-15 minutes. The main thing is that the ring falls into the capable hands of a jeweler who has earned positive reviews for his work.

How to reduce ring size?

To make a ring smaller, jewelers use three methods.

• Cutting out a piece of the rim.

This method is used for rings decorated with precious stones to prevent damage to the overall structure of the jewelry. It is recommended to first remove all stones from the setting, especially when soldering the ring with an open fire.

For rings made of white gold, with enamel or mother of pearl, laser soldering is used.

If, the jeweler cuts a piece of the base 3.14 mm long, into two sizes - 6.28 mm, and then grinds and polishes the joint.

• Filling the rim.

This method is usually used to reduce the size of wedding rings without precious stones or decorative elements.

If the ring needs to be adjusted by half a size, it is simply knocked down, and if by 1-1.5-2 sizes, it is preheated, increasing the elasticity of the metal, and then knocked down to the desired size. The carbon deposits are cleaned off and the product is polished.

• Insertion without sawing.

The method is expensive, but eliminates all signs of impact on the decoration. The ring remains the same, only its inner diameter decreases. This happens by soldering a base metal plate or an additional ring into the inside of the product.

How to increase your ring size?

In this case, jewelers also practice three methods.

• Boring of the rim.

The method is simple, but applicable only for rings with a thick rim that need to be increased by half a size. Its main disadvantage is the loss of ground gold, however, sometimes this method is the only one that allows you to increase the size of a complex-shaped ring with stones or decor without damage.

• Mechanical stretching.

This method is used to increase the size of ordinary wedding and signet rings. The ring should not be too wide - no more than 10-12 mm. It is easier to stretch thin rings, even by 2 sizes, but this method is not suitable for too thin products - they may burst.

The jeweler first determines the amount by which the ring should be enlarged, then heats the product, puts it on the crossbar and, by rotating its handle, achieves the required size. At the end of the work, removes irregularities, grinds and polishes the ring.

• Metal insert.

Or, by setting the stone, you can increase the size only by making an insert of a similar metal. The product is cut from the bottom and expanded to the required size, and a pre-prepared insert is soldered into the resulting space. Before soldering, the insert and ring are boiled in boric acid to maintain shine. After final processing, the ring looks like a single whole.

From precious metal, it will take about 10 minutes. This procedure is simple and is usually done in front of you. It is important that the jewelry falls into the hands of a skilled jeweler. Here's what you need to know about this procedure.

Special attention when adjusting ring size with gems require stones. For example, the most “given” and favorite stone “with meaning” is a diamond. But when heated, when the ring is reduced or enlarged to avoid trouble, It is better to remove the insert from the base of the ring. Even if it is a durable diamond.

If you see that the master begins work without removing the stone from the base, stop him and demand this. Let it cost a little more. Remember that the miser pays twice

How to reduce your ring size

Cutting out a piece of shank. The procedure is most often carried out on rings with stones, where it is important not to damage the overall structure. To reduce the ring by one size, a piece of the shank (base) about 3.14 mm long is cut out, and the joint is ground and polished.

Hammering the shank of the ring. The ring is put on the bolt, and then the metal is heated and knocked down. This method is recommended for adjusting the size of simple rings without stones or decorative elements. This is how classic wedding rings are customized. If the ring needs to be reduced by half a size, the ring is not heated, but simply knocked down. When it is a size or two, the metal is heated gradually and knocked down to the required parameters.

Downsizing. Shrinkage of the ring shank when heated

Insertion without sawing. An additional base metal plate or another additional ring is inserted into the inner part of the ring. This is one of the most expensive methods. With this correction, signs of impact on the ring are excluded, only the internallower diameter of the product.

How to increase your ring size

Ring boring. The inner layer of the tire is cut out. This is the easiest and most painless way to increase your ring size by half a size. Boring- sometimes the only way to increase the size of a ring is with a thick shank, stones and decorative elements without damage.

Mechanical stretching of metal. Suitable for increasing the size of classic rings without inserts and stones, most often wedding rings. In this case, the ring should not be too wide, about 10mm. First, the jeweler calculates the size by which the ring needs to be enlarged, and then, by heating and rotating it on the crossbar, he achieves the desired parameters. Cleaning and polishing the ring at the end of work completely eliminates any traces of impact. But this method is not suitable for rings that are too thin; they may simply burst.

Metal insert. When the elements of a ring (complex stone setting, ornament) have high artistic value, the only way to increase its size is make an insert from similar metal. The ring is cut from the bottom, expanded to the required size, and an insert made of the same metal (of the same standard, color and shade) is soldered in. For shine and gloss, even before the procedure, the ring is immersed in a solution of boric acid. As a result, you will not be able to distinguish a corrected ring from a new one.

At the end of all procedures, the master polishes the ring and the stone itself. Then he wipes it with napkins soaked in a special solution.

Polishing and daily cleaning of jewelry

Ideally, such services are not needed. To do this, it is better to try on a hundred times, and only then make the final choice!

The ring is an indispensable decoration for fingers, known since ancient times. Today you can choose a ring of almost any size. But sometimes an unpleasant situation occurs - a favorite ring suddenly becomes small or a gift does not fit on your finger. In this case, rolling it out in a jewelry salon can help. But this is quite expensive, so it is better to find out how to roll out a ring at home and whether it is even possible. It wouldn’t hurt to find out whether this particular product can be enlarged or not.

How to roll out a ring at home?

What kind of rings can you roll out?

Increasing the ring size by rolling has some features that must be taken into account. Unfortunately, many types of rings are not rolled out due to completely natural processes during rolling.

1. Rings with rotating inserts.

2. In most cases, the dimensions of bimetallic rings do not change.

3. If there is a drawing or stone.

Based on this list, the answer to the question of whether it is possible to roll out a ring with stones is one: absolutely not. In this case, only one metal base may remain, and the pebbles will leave their nests due to stretching and deformation of the metal.

Is it possible to roll out the ring yourself?

Unfortunately, it is quite difficult to increase your ring size at home. Because for this, at a minimum, you will need experience and a special tool. Not every man has a special deadbolt, a gas burner and a hammer with a rubber surface in his garage or closet. In most cases, a special rolling device is used. But even if all this is present, lack of experience can lead to irreparable damage to the ring.

But the technology used by jewelers to increase sizes using a crossbar and a special device is quite clear.

· First, the ring is heated red-hot using a gas burner.

· Then they allow it to cool on its own, while preparing the tools.

The reason for this action may be due to the wrong choice of jewelry size. Perhaps someone simply didn’t know the size and couldn’t find the right ring. It happens that the hand has recovered or, conversely, at the time of purchase it was swollen, swollen, and then lost weight. But is it difficult to adjust the product to size? And what is the best way to do this?

Simple and safe option with boring

It is quite possible to increase the size of a ring with a stone in the simplest and safest way - through boring the product. This procedure involves cutting out the inner layer of the tire. It allows you to enlarge your ring by about half a size. The method is ideal for products with decorative and precious stones that have a wide shank.

The process is usually performed using a special machine with a clamp. It is not suitable for rings that are too thin. Only for wide ones. Takes approximately 10-30 minutes. However, this method has its drawbacks. Due to the use of rolling or boring, the thickness of the tire will decrease. It will become thinner than its original thickness.

We increase the size by rolling out

There is another simple option that allows you to increase the size of your wedding ring or any other item. It involves rolling out metal. It is performed using special equipment and a machine. As with boring, it is necessary to narrow the shank of the ring. IN in this case it will also become narrower, and the size of the ring itself will increase.

Metal inserts

To increase the size of the ring, you can use inserts from a suitable metal. During the work, the master carefully cuts the shank from below (in the place where it touches the finger). And then he begins to push it apart as much as it will be necessary to increase the size of the decoration. For example, if you need to increase the product by one size, it needs to be expanded by approximately 3.14 mm.

The resulting space is covered with a small piece of metal, completely matching the parameters and appearance of the ring itself. In this case, the joints are treated not only with a laser, but also with fire. To give decoration natural shine it is necessary to immerse it in a solution with boric acid. After this, you will not even be able to distinguish where the original metal patch is located, and where the factory tire begins.

The type of soldering directly depends on the existing shape of the stone on the product. You can increase the ring size by soldering an insert made of identical metal in at least an hour. Sometimes it takes more time to process a product.

Using the Pinocchio tool

To increase the size of jewelry, a device called “Pinocchio” is often used. During the procedure, a ring is usually put on it and they begin to stretch it by increasing the size of the cone. However, before you increase the ring size using Pinocchio, you need to heat the product. IN otherwise you risk tearing the jewelry or deforming it.

According to experts, this option is perfect for working with wedding rings and products of the most common round shape. On average, such work does not take more than 25-30 minutes.

Application of mechanical stretching of metal

When answering the question of whether it is possible to increase the size of the ring, one cannot help but recall the method of mechanical stretching of the metal. However, the method is not suitable for products with complex decorative patterns. The presence of a small stone in this case is allowed. The ring itself should also not be too wide. Its approximate thickness should not be more than 10 mm.

During the work process, the master usually performs calculations and determines the size. After that, he rotates the fixed decoration on a special crossbar and heats it. Thus, he manages to achieve suitable dimensions of the product. At the end of the procedure, it is necessary to eliminate roughness and uneven areas of the tire. To do this, it is cleaned and polished.

Making a metal insert without cutting out

During the work, the master uses an additional metal plate made of a similar metal. Or instead, he uses an additional ring inserted inside your product. This method, according to jewelers, is considered the most expensive. However, it does not have any physical effect on the main decoration. All resizing work is carried out with the internal inserts used. As a result, it is not the ring itself that changes, but its internal diameter.

How to increase ring size at home

Changing the size of a product is not as easy as it might seem at first glance. Therefore, in most cases, experts recommend not even trying. There is a huge risk that you will damage the product. In such cases, it is best to contact specialists.

However, if you are still determined, you will need the following tools for the job:

• Special crossbar.
• Gas-burner.
• Small rubber mallet.

But keep in mind that having all these tools does not give any guarantee that you will succeed. First, you need to take the ring and clamp it, for example, with pliers or round nose pliers. Then you need to turn on the burner and heat the product to its characteristic red color. Next, you should leave the decoration for a few minutes so that it cools down a little. And when it is slightly warm, all you have to do is insert it into the crossbar and start rolling.

What products can be rolled out?

Before you start rolling, keep in mind that not all products can be processed in this way. For example, you cannot use rolling for rings with rotating inserts. Not worth trying this method and for bimetallic products. It is not recommended to roll out even if there are inscriptions, engravings and drawings.

If your rings contain stones, you must carefully remove them before performing the procedure. Otherwise, when the ring is stretched, they may leave their “nests” and jump out. At the end of the work, you can return the stones back and securely fix them using pliers, for example.

Be careful!

Be careful! So that the expression “The miser pays twice” does not apply to you, do not save. If you have a product that is not suitable in size, but is very expensive for you, give it to professionals. Let the work cost money, but it will save appearance your decoration.